Basic Info.
Product Description
- 2, 4 and 8-channel analog input (AI) modules
- Apart from the standard type of delivery in an individual package, selected I/O modules and BaseUnits are also available in a pack of 10 units. The pack of 10 units enables the amount of waste to be reduced considerably, as well as saving the time and cost of unpacking individual modules.
For different requirements, the digital input modules offer:
- Function classes Basic, Standard, High Feature and High Speed
- BaseUnits for single or multiple-conductor connection with automatic slot coding
- Potential distributor modules for system-integrated expansion with potential terminals
- Individual system-integrated potential group formation with self-assembling voltage busbars (a separate power module is no longer required for ET 200SP)
- Option of connecting current, voltage and resistance sensors, as well as thermocouples
- Option of connecting force and torque sensors
- Energy Meter for recording up to 600 electrical variables
- Clear labeling on front of module
- LEDs for diagnostics, status, supply voltage and faults
- Electronically readable and non-volatile writable rating plate (I&M data 0 to 3)
- Extended functions and additional operating modes in some cases
- MSI operating mode (simultaneous reading of input data from as many as three other controllers)
- Oversampling operating mode (n-fold equidistant acquisition of analog values within one PN cycle for increasing the time resolution for slow CPU cycles)
- Isochronous mode (simultaneous equidistant reading in of all analog values)
- Scalable measuring range (adaptation of measuring range, increase of the 16-bit resolution by adapting the measuring range to a limited section)
- Scaling of the measured values (transmission of the analog value normalized to the required physical value as a 32-bit floating point value)
- Internal compensation of the line resistance for thermocouples by means of terminal temperature measurement in the BaseUnit for BU type A1
- Internal compensation also for 2-conductor resistance test by means of adjustable line resistance
- Calibration during runtime
- Single-channel galvanic isolation
- HART communication
- Re-parameterization during operation
- Firmware update
- Diagnostics of wire break, short-circuit, overflow, underflow
- Two upper and lower hardware interrupts in each case, interference frequency suppression, smoothing
- Value status (optional binary validity information of the analog value status in the process image)
- Supports the PROFIenergy profile
- Optional accessories
- Labeling strips (film or card)
- Equipment labeling plate
- Color-coded label with module-specific CC code
- Shield terminal
A quick and clear comparison of the functions of the AI modules is offered by the TIA Selection Tool.
Overview of analog input modules
Analog input | PU | Article No. | CC code | BU type |
|---|---|---|---|---|
AI 8 x I 2/4-wire BA | 1 | 6ES7134-6GF00-0AA1 | CC01 | A0, A1 |
AI 2 x U ST | 1 | 6ES7134-6FB00-0BA1 | CC00 | A0, A1 |
AI 8 x U BA | 1 | 6ES7134-6FF00-0AA1 | CC02 | A0, A1 |
AI 4 x U/I 2-wire ST | 1 | 6ES7134-6HD00-0BA1 | CC03 | A0, A1 |
AI 4 x U/I 2-wire ST | 10 | 6ES7134-6HD00-2BA1 | CC03 | A0, A1 |
AI 2 x I 2/4-wire ST | 1 | 6ES7134-6GB00-0BA1 | CC05 | A0, A1 |
AI 4 x I 2/4-wire ST | 1 | 6ES7134-6GD00-0BA1 | CC03 | A0, A1 |
AI 4 x I 2/4-wire ST | 10 | 6ES7134-6GD00-2BA1 | CC03 | A0, A1 |
AI 4 x I 2-wire 4 ... 20 mA HART | 1 | 6ES7134-6TD00-0CA1 | CC03 | A0, A1 |
AI 2 x U/I 2/4-wire HF | 1 | 6ES7134-6HB00-0CA1 | CC05 | A0, A1 |
AI 2 x U/I 2/4-wire HS With two operating modes:
| 1 | 6ES7134-6HB00-0DA1 | CC00 | A0, A1 |
AI 8 x RTD/TC 2-wire HF | 1 | 6ES7134-6JF00-0CA1 | CC00 | A0, A1 |
AI 8 x RTD/TC 2-wire HF | 10 | 6ES7134-6JF00-2CA1 | CC00 | A0, A1 |
AI 4 x RTD/TC 2/3/4-wire HF | 1 | 6ES7134-6JD00-0CA1 | CC00 | A0, A1 |
AI 4 x RTD/TC 2/3/4-wire HF | 10 | 6ES7134-6JD00-2CA1 | CC00 | A0, A1 |
AI 4 x TC High Speed | 1 | 6ES7134-6JD00-0DA1 | CC00 | A0, A1 |
AI 2 x SG 4/6-wire High Speed | 1 | 7MH4134-6LB00-0DA0 | CC00 | A0 |
AI Energy Meter CT ST | 1 | 6ES7134-6PA01-0BU0 | -- | U0 |
AI Energy Meter RC ST | 1 | 6ES7134-6PA21-0BU0 | -- | U0 |
AI Energy Meter CT HF | 1 | 6ES7134-6PA01-0CU0 | -- | U0 |
AI Energy Meter RC HF | 1 | 6ES7134-6PA21-0CU0 | -- | U0 |
Application
The measured values of analog sensors (current, voltage, resistance, temperature etc.) can be recorded and transferred to the higher-level controller via the analog input modules.
Design
Usable BaseUnits (BU)
BaseUnits with an appropriate number of terminals are available for single or multi-conductor connection.
All variants that correspond to the BU type of the I/O module used can be used as BaseUnits (see Selection and ordering data). The BaseUnits that can be used for the respective module are noted on the front side of the module.
Potential distributor modules
With the new potential distributor modules for SIMATIC ET 200SP, additional potentials required within an ET 200SP station can be set up quickly and in a space-saving manner. Due to the free combinability of PotDis-BUs and PotDis-TBs, the potential distributor modules allow a large number of design variants and thus simple adaptation to individual needs. Within the station, existing potentials can be multiplied or even new potential groups can be formed. With 36 terminals per 15 mm width, the PotDis modules require very little space without compromising on the conductor cross-sections (maximum 2.5 mm²). They allow the connection of voltages up to 48 V DC with a maximum current carrying capacity of 10 A, and with the PotDis-TB-BR-W even up to 230 V AC/10 A as well as the possibility to connect a protective conductor.
Typical applications for the PotDis modules in connection with AI modules are, for example, the supply of supply voltage for sensors.
Potential group formation
A light BU separates the self-assembling, internal voltage buses (P1, P2, AUX) and thus opens a new potential group. The supply voltage of a potential group must be fed in at the light BU of this potential group.
A dark BU forwards the supply voltage of the adjacent light BU on the left via the self-assembling voltage buses P1, P2 and AUX. A new infeed is therefore only required on the next light BU to the right. The setting of a further light BU is required whenever
- a new potential group is to be formed (for example, for isolating the supply voltage from module groups) or
- the maximum current simultaneously required by the potential group exceeds the permissible limit of 10 A.
Color identification of the terminals
The potentials at the terminals of the BaseUnit are defined by the inserted I/O module in each case. To prevent wiring faults, the potentials of the terminals can optionally be identified by means of module-specific color-coded labels. The color-coded label that matches the respective I/O module is defined by the color code CCxx of the I/O module. This color code is also printed on the front of the module.
In BaseUnits with the additional ten internally jumpered AUX terminals or 2x5 additional terminals, these can also be identified with color-coded labels. For the ten AUX terminals, color-coded labels are available in red, blue, and yellow/green.
Labeling
Labeling strips
Labeling strips can be inserted on the front of the interface modules or I/O modules and individually labeled via STEP 7, macros, etc. No special additional holder is required. If required, they can be easily replaced with the component.
Equipment labeling plates
Equipment labeling plates enable the equipment to be easily identified (e.g. compliant with EN 81346). They are easily plugged onto the required component (interface modules, I/O modules and BaseUnits) and when required, they can be easily replaced with the component.
The following labeling components are available:
Film labeling strips, light-gray, roll with 500 strips, perforated, for thermal transfer printers
- Film labeling strips, yellow, roll with 500 strips, perforated, for thermal transfer printers
- Card labeling strips (180 g/m2), light gray, ten DIN A4 sheets with 100 strips each, perforated, for laser printer
- Card labeling strips (180 g/m2), yellow, ten DIN A4 sheets with 100 strips each, perforated, for laser printer
- Equipment labeling plates, white, ten sheets each with 16 labels, for thermal transfer card printers or labels
System-integrated shield connection
For the space-saving and EMC-optimized connection of cable shields, a shield connection is available that is quick and easy to mount. This consists of one shield connection element that can be plugged onto the BaseUnit and one shield terminal for each module. The low-impedance connection to the functional ground (DIN rail) is achieved without any additional wiring by the user.
Data sheet 6ES7134-6GF00-0AA1
| SIMATIC ET 200SP, Analog input module, AI 8XI 2-/4-wire Basic, suitable for BU type A0, A1, Color code CC01, Module diagnostics, 16 bit | |
| General information | |
| Product type designation | AI 8xI 2-/4-wire BA from FS04 Yes BU type A0, A1 CC01 |
| HW functional status | |
Firmware version
| |
| usable BaseUnits | |
| Color code for module-specific color identification plate | |
| Product function | |
| Yes; I&M0 to I&M3 No No |
| Engineering with | |
| V13 SP1 V5.5 SP3 / - One GSD file each, Revision 3 and 5 and higher GSDML V2.3 |
| Operating mode | |
| No No |
| CiR - Configuration in RUN | |
| Reparameterization possible in RUN | Yes No |
| Calibration possible in RUN | |
| Supply voltage | |
| Rated value (DC) | 24 V 19.2 V 28.8 V Yes |
| permissible range, lower limit (DC) | |
| permissible range, upper limit (DC) | |
| Reverse polarity protection | |
| Input current | |
| Current consumption, max. | 25 mA; without sensor supply |
| Encoder supply | |
| 24 V encoder supply | |
| Yes Yes 0.7 A; total current of all encoders/channels |
| Power loss | |
| Power loss, typ. | 0.7 W; Without encoder supply voltage |
| Address area | |
| Address space per module | |
| |
| Hardware configuration | |
Automatic encoding
| Yes Yes Type A |
| Selection of BaseUnit for connection variants | |
| BU type A0, A1 BU type A0, A1 BU type A0, A1 + potential distributor module |
| Interrupts/diagnostics/status information | |
| Diagnostics function | Yes |
| Alarms | |
| Yes No |
| Diagnoses | |
| Yes |
Shenzhen Aimiqu Technology Co., Ltd established in March 2016, the business scope including general management project is automation equipment accessories, instruments and meters, valves, switches, electronic semiconductor, electronic products, digital products, electronic components, communications products, computer software and hardware, security equipment, energy conservation and environmental protection products, intelligent household products; Operating electronic commerce; Domestic trade, import and export of goods and technology. Electrical automation import and export trade for the main business.
Since its establishment, Aimiqu has been providing industrial automation services, providing customers with high-quality products and automation solutions. In the long-term business process, Emicic has established good partnerships with well-known international manufacturers .
At the same time,Aimiqu attaches great importance to product research and development, invested a lot of funds, independent production and development of electrical equipment such as power distribution cabinet and put into use. For customers in product performance testing, automated production lines, electronic equipment, wire and cable, and other aspects of energy saving equipment reform and development, design, transform the multitude of automation equipment and automation control system, and provide a reliable and professional support, and pre-sale, sale and after-sale services - dragon, by the customer the consistent high praise.
